Suitable Sink Single Handle Antique Brass Centerset Bathroom Sink Faucet
Overview :Add to Wish List
Online Wholesale Electronics at discount prices!
>Wholesale Home & Garden
>Wholesale Antique Faucets
>Suitable Sink Single Handle Antique Brass Centerset Bathroom Sink Faucet
Overview :Add to Wish List
Save $19.67 Centerset Installation Type Two Handles Gold Centerset Bathroom Sink Faucet $ 65.60
Save $36.90 Ceramic Valve Type Two Handles Antique Brass Widespread Bathroom Sink Faucet $ 123.03
Save $27.69 Suitable Kitchen Two Handles Antique Brass Centerset Kitchen Faucet $ 92.32
Save $20.36 Brass Material Two Handles Antique Brass Centerset Bathroom Sink Faucet $ 67.85
Save $40.77 Brass Material Two Handles Antique Brass Wall-mount Bathtub Faucet $ 135.93
Save $45.28 Two Handles Antique Brass Widespread Bathroom Sink Faucet $ 150.96
|Product Description||Single Handle Antique Brass Centerset Bathroom Sink Faucet with Hot and Cold Switch|
|Valve Type||Ceramic Valve
|Faucet Total Height||33 cm
|Spout Height||20 cm|
|Spout Length||11 cm
|Inner Box Size||35 x 25 x 7 cm|
|What's in the box||1 x Faucet;
2 x Hose
1 x Accessory Set;
1 x Installation Instruction;
Step 2: Attach the Water Supply Tubes
A: Wrap the threads of the water-supply valve with Teflon tape. Although most plumbers use only Teflon tape, some plumbing supply manufacturers also recommend using plumber’s putty.
B: Thread the water supply nut onto the shut-off valve. Tighten the nut with a wrench.
C: Wrap the threads on the faucet shank with Teflon tape, and then thread the water supply nut onto the faucet shank.
D: Tighten the nut with a wrench.
Step 3: Connect the Faucet Lift Rod
A-1: From the top of the sink, insert the lift-rod into the faucet.
A-2: From under the sink, make sure the pivot-rod is in the down position. Insert the lift-rod into the lift-rod strap. Tighten the screw.
B-1: From the top of the sink, make sure the lift-rod opens and closes the drain plug as desired.
B-2: Make any needed adjustments by loosening the lift-rod strap screw and repositioning the lift-rod.
B-3: If you need to connect the lift-rod strap to the pivot rod, slide one end of the spring clip onto the pivot-rod.
B-4: Make sure that both the pivot -rod and the lift-rod are in the down position. Insert the pivot-rod in the closest hole in the lift-rod strap.
B-5: Slide the other end of the pivot-rod. Make sure the lift-rod opens and closes the drain plug as desired.
C-1: Make minor adjustments by loosening the lift-rod strap screw and repositioning the lift-rod.
C-2: Make major adjustments by removing the spring clip and moving the pivot-rod to a different hole in the lift-rod strap.
Step 4: Flush the Faucet
A-1: Anytime you work on plumbing, filings, chips, and other debris can fall into the plumbing pipes.
A-2: This debris can damage the sealing surfaces inside the faucet and cause leaks.
A-3: Remove aerator and black sealing gasket above it.
A-4: Before turning on the water supply, make sure the faucet handles are open (on position) in order to remove the debris without causing damage.
B: Open both water supply valves under the sink.
C-1: Allow the water to run for 15 seconds.
C-2: Close the faucet handles (turn off).
D: Make sure any debris is cleaned from the aerator screen.
E: Replace the aerator.