Single Handle LED Chrome Waterfall Bathroom Sink Faucet(Blue)
Overview :Add to Wish List
Online Wholesale Electronics at discount prices!
>Wholesale Home & Garden
>Wholesale Waterfall Faucets
>Single Handle LED Chrome Waterfall Bathroom Sink Faucet(Blue)
Overview :Add to Wish List
Save $50.51 Ceramic Valve Valve Type Two Handles Chrome Widespread Waterfall Bathtub Faucet $ 168.36
Save $20.88 Single Handle Chrome Waterfall Sink Faucet $ 69.62
Save $45.80 Chrome Finish Two Handles Chrome Widespread Waterfall Bathtub Faucet $ 152.67
Save $20.62 Single Handle Chrome Waterfall Sink Faucet $ 68.73
Save $47.18 WideSpread Installation Type Two Handles Waterfall Bathroom Sink Faucet $ 157.28
|Product Description||Single Handle LED Chrome Waterfall Sink Faucet with Hot and Cold Switch|
|Valve Type||Ceramic Valve|
|Faucet Total Height||18.3 cm|
|Spout Height||5 cm|
|Spout Length||Φ14.5 cm|
|Sink Installation hole Diameter||3.5-5 cm|
|Shipping Weight||2 kg|
|What's in the box||1 x Faucet
2 x Hose
1 x Accessory Set
1 x Installation Instruction
|Inner box size||29 x 22 x 15 cm|
50~100℃ Red (Flashing).
Please kindly note image below is just for your reference.
Different faucets are shipped with different accessories.
B: Other accessories for fixture
Tools You Need for Installation
General Faucet Installation Instruction
Please kindly note that this is just a general instruction, each faucet you buy from us has installation instruction with details inside package.
Step 1: Position the Faucet
A: Begin installing your faucet by placing the gasket and faucet in position on the sink.
B: From under the sink, thread the plastic mounting nuts onto the faucet shanks. Be sure the large side of each plastic mounting nut is up.
C: From the top of the sink, check the faucet and gasket position.
D: From under the sink tighten the mounting nuts, making certain not to over-tighten which could damage the nuts and make them difficult to remove in the future.
Step 2: Attach the Water Supply Tubes
A: Wrap the threads of the water-supply valve with Teflon tape. Although most plumbers use only Teflon tape, some plumbing supply manufacturers also recommend using plumber’s putty.
B: Thread the water supply nut onto the shut-off valve. Tighten the nut with a wrench.
C: Wrap the threads on the faucet shank with Teflon tape, and then thread the water supply nut onto the faucet shank.
D: Tighten the nut with a wrench.
Step 3: Connect the Faucet Lift Rod
A-1: From the top of the sink, insert the lift-rod into the faucet.
A-2: From under the sink, make sure the pivot-rod is in the down position. Insert the lift-rod into the lift-rod strap. Tighten the screw.
B-1: From the top of the sink, make sure the lift-rod opens and closes the drain plug as desired.
B-2: Make any needed adjustments by loosening the lift-rod strap screw and repositioning the lift-rod.
B-3: If you need to connect the lift-rod strap to the pivot rod, slide one end of the spring clip onto the pivot-rod.
B-4: Make sure that both the pivot -rod and the lift-rod are in the down position. Insert the pivot-rod in the closest hole in the lift-rod strap.
B-5: Slide the other end of the pivot-rod. Make sure the lift-rod opens and closes the drain plug as desired.
C-1: Make minor adjustments by loosening the lift-rod strap screw and repositioning the lift-rod.
C-2: Make major adjustments by removing the spring clip and moving the pivot-rod to a different hole in the lift-rod strap.
Step 4: Flush the Faucet
A-1: Anytime you work on plumbing, filings, chips, and other debris can fall into the plumbing pipes.
A-2: This debris can damage the sealing surfaces inside the faucet and cause leaks.
A-3: Remove aerator and black sealing gasket above it.
A-4: Before turning on the water supply, make sure the faucet handles are open (on position) in order to remove the debris without causing damage.
B: Open both water supply valves under the sink.
C-1: Allow the water to run for 15 seconds.
C-2: Close the faucet handles (turn off).
D: Make sure any debris is cleaned from the aerator screen.
E: Replace the aerator.